Fully Reinforced Buoyancy Control or Neutral Buoyancy Double Carcass Hose

Fully Reinforced Buoyancy Control or Neutral Buoyancy Hose Main Carcass:
  • Main Lining / Inner Tube: Smooth, oil and fuel resistant Pure Seamless and Extruded Acrylontrile-Butadiene-Rubber (NBR);
  • Safety Lining: special construction to prevent defects or damage cause by incidental tearing or superficial damages of the main linig;
  • Reinforcements: Multiple Plies of High Tensile Textile cord. One embedded helical Body Steel wire.
  • Cover: Black Syntetic Rubber Smooth oil and fuel resistant.
  • Single Carcass And Double Carcass

Product Details

Fully Reinforced Buoyancy Control or Neutral Buoyancy Hose
  1. the second or third hose in mainline
  2. rated working pressure: 21 bar
  3. minimum reserve buoyance: 20% or according to customer requirements
  4. electrical continuity: electrical continuous or discontinuous
  5. leak detection system: after the failure of the primary carcass, the detector will react to the leakage to remind the operator to remove the damaged hose to avoid economic loss and environmental pollution.
  6. cover: PU or rubber
Fully Reinforced Buoyancy Control or Neutral Buoyancy Hose Main Carcass:
  • Main Lining / Inner Tube: Smooth, oil and fuel resistant Pure Seamless and Extruded Acrylontrile-Butadiene-Rubber (NBR);
  • Safety Lining: special construction to prevent defects or damage cause by incidental tearing or superficial damages of the main linig;
  • Reinforcements: Multiple Plies of High Tensile Textile cord. One embedded helical Body Steel wire.
  • Cover: Black Syntetic Rubber Smooth oil and fuel resistant
  • Single Carcass And Double Carcass.
Fully Reinforced Buoyancy Control or Neutral Buoyancy Hose Floatation:
  • Floating Material : Closed cell Foam. Fully Reinforced Buoyancy Control or Neutral Buoyancy Hose Outer Cover:
  • Smooth black, Synthetic Rubber Resistant to Abrasion, Oil, Sea Water and Sunlight.
  • Helical Orange strip.
  • Polyurethane Orange in Colour cover available on request.
Fully Reinforced Buoyancy Control or Neutral Buoyancy Hose Fittings: End connections built in during manufacture. ASME B 16.5 Class 150lb or 300lb Weld Neck Flat Face or Raised Face on request. Fully Reinforced Buoyancy Control or Neutral Buoyancy Hose Tests: All tests according to GMPHOM 2009 and Customer detail.  

Tail Full Floating Hose Main Carcass:

  • Main Lining / Inner Tube: Smooth, oil and fuel resistant Pure Seamless and Extruded Acrylontrile-Butadiene-Rubber (NBR);
  • Safety Lining: special construction to prevent defects or damage cause by incidental tearing or superficial damages of the main linig;
  • Reinforcements: Multiple Plies of High Tensile Textile cord. One embedded helical Body Steel wire.
  • Cover: Black Syntetic Rubber Smooth oil and fuel resistant.
  • Single Carcass And Double Carcass

Product Details

Tail Full Floating Hose Construction & Material

Tail Full Floating Hose Main Carcass:

  • Main Lining / Inner Tube: Smooth, oil and fuel resistant Pure Seamless and Extruded Acrylontrile-Butadiene-Rubber (NBR);
  • Safety Lining: special construction to prevent defects or damage cause by incidental tearing or superficial damages of the main linig;
  • Reinforcements: Multiple Plies of High Tensile Textile cord. One embedded helical Body Steel wire.
  • Cover: Black Syntetic Rubber Smooth oil and fuel resistant.
  • Single Carcass And Double Carcass

Tail Full Floating Hose Floatation:

  • Floating Material : Closed cell Foam. Tail Full Floating Hose Outer Cover:
  • Smooth black, Synthetic Rubber Resistant to Abrasion, Oil, Sea Water and Sunlight.
  • Helical Orange strip.
  • Polyurethane Orange in Colour cover available on request.

Tail Full Floating Hose Fittings: End connections built in during manufacture. ASME B 16.5 Class 150lb or 300lb Weld Neck Flat Face or Raised Face on request.
Tail Full Floating Hose Tests: All tests according to GMPHOM 2009 and Customer detail.

 

 
Gel ChromatographyTensiometer DisplayWire Torsion Tester

Inspection

1. Material Tests2. Adhesion Tests3. Buoyancy Recovery Test
In addition to the quality control tests that the Manufacturer will have in place for compounds and materials listed in the following table, the following Material Tests should be conducted every three months. The adhesion strength between all composite plies of the hose Body will be determined by peel testing in accordance with ISO 36 using strip test pieces. The measured adhesion strength will be not less than 6 N/mm. Adhesion tests will also be conducted on the integral buoyancy medium at three monthly intervals. The sample will have a minimum internal diameter of 300 mm and will be at least 500 mm long.
4. Weight Test5. Collar Test6. Torsion Test
7. Tensile Test On Pressurized Hose8.Dynamic Test Bending Load9./10. Minimum Bend Radius Test/Bending Stiffness Test
11. Hydrostatic Pressure Test12. Kerosene Test13. Vacuum Test
14. Electrical Test15. Burst TestDouble Carcass Burst Test16. Lifting Lug Acceptance Test